< back to main site

Publications

Items where Subject is "Advanced Materials > Composites"

Up a level
Export as [feed] RSS
Group by: Authors | Item Type
Jump to: A | B | C | D | G | H | J | K | L | M | N | P | R | S | U | W | Y
Number of items at this level: 152.

A

Aktas, A; Boyd, S W*; Shenoi, R A* (2015) Cure and strain monitoring of novel unsaturated polyester/phenolic resin blends in the vacuum infusion process using fibre Bragg gratings. J. Compos. Mater., 49 (29). pp. 3599-3608.

Aktas, A; Krishnan, L*; Kandola, B*; Boyd, S W*; Shenoi, R A* (2015) A cure modelling study of an unsaturated polyester resin system for the simulation of curing of fibre-reinforced composites during the vacuum infusion process. J. Compos. Mater., 49 (20). pp. 2529-2540.

Aktas, A; Sims, G D; Lira, C*; Stojkovic, M* (2016) Survey of procedures in use for permeability measurements in liquid composite moulding processes. NPL Report. MAT 82

B

Blazquez, A*; Mantic, V*; Paris, F*; McCartney, L N (2008) Stress state characterization of delamination cracks in [0/90] symmetric laminates by BEM. Int. J. Solids Struct., 45 (6). pp. 1632-1662.

Bowen, C R*; Dent, A C*; Nelson, L J*; Stevens, R*; Cain, M G; Stewart, M (2006) Failure and volume fraction dependent mechanical properties of composites sensors and actuators. Proc. Inst. Mech. Eng. C, J. Mech. Eng. Sci., 220 (11). pp. 1655-1664.

Bowen, C R*; Dent, A C*; Stevens, R*; Cain, M G; Stewart, M (2005) Determination of critical and minimum volume fraction for composite sensors and actuators. In: 4M 2005 - First International Conference on Multi-Material Micro Manufacture, 2005, Cardiff, UK.

Broughton, W R (2006) In-plane testing of thick composites: a review. NPL Report. DEPC-MPR 057

Broughton, W R (2001) Thick composites. NPL Report. CMMT(A)263

Broughton, W R; Crocker, L E; Gower, M R L (2002) Design requirements for bonded and bolted composite structures. NPL Report. MATC(A)65

Broughton, W R; Crocker, L E; Lodeiro, M J (2006) Characterising micro and nanoscale interfaces in advanced composites: a review. NPL Report. DEPC-MPR 055

Broughton, W R; Gower, M R L; Lodeiro, M J; Pilkington, G D; Shaw, R M (2010) Assessment of quasi-static and fatigue loaded notched GRP laminates using digital image correlation. Appl. Mechan. Mater., 24-25. pp. 407-412.

Broughton, W R; Gower, M R L; Lodeiro, M J; Pilkington, G D; Shaw, R M (2011) An experimental assessment of open-hole tension-tension fatigue behaviour of a GFRP laminate. Compos. A, Appl. Sci. Manuf., 42 (10). pp. 1310-1320.

Broughton, W R; Gower, M R L; Lodeiro, M J; Shaw, R M (2012) Good practice guide for monitoring deformation and damage in fibre-reinforced plastics. Measurement Good Practice Guide. 123

Broughton, W R; Gower, M R L; Lodeiro, M J; Shaw, R M (2010) Good practice guide for the generation and assessment of fatigue data for fibre-reinforced plastics. Measurement Good Practice Guide. 115

Broughton, W R; Gower, M R L; Lodeiro, M J; Shaw, R M (2001) Through-thickness testing of polymer matrix composites. NPL Report. MATC(MN)06

Broughton, W R; Koukoulas, T (2011) Seeing is believing - optical techniques for measuring nanoparticle content and dispersion in polymeric matrices. Mater. World, 19 (5). pp. 20-21.

Broughton, W R; Koukoulas, T; Woolliams, P D; Williams, J*; Rahatekar, S S* (2013) Assessment of nanoparticle loading and dispersion in polymeric materials using optical coherence tomography. Polym. Test., 32 (7). pp. 1290-1298.

Broughton, W R; Lodeiro, M; Sims, G D (1996) Experimental validation of shear test methods for through-thickness properties. In: ECCM-7 7th European Conference on Composite Materials, 14-16 May 1996, London, UK.

Broughton, W R; Lodeiro, M J (2000) Cyclic fatigue of continuous unidirectional polymer matrix composites. NPL Report. CMMT(A)249

Broughton, W R; Lodeiro, M J (1999) Cyclic fatigue of continuous unidirectional polymer matrix composites: an interim report. NPL Report. CMMT(A)186

Broughton, W R; Lodeiro, M J (2000) Environmental and fatigue testing of fibre-reinforced polymer composites. NPL Report. CMMT(MN)67

Broughton, W R; Lodeiro, M J (2000) Environmental and fatigur testing of fibre bundles and impregnated strands. NPL Report. CMMT(MN)63

Broughton, W R; Lodeiro, M J (2000) Fatigue testing of composite laminates. NPL Report. CMMT(A)252

Broughton, W R; Lodeiro, M J (2000) Techniques for monitoring water absorption in fibre-reinforced polymer composites. NPL Report. CMMT(MN)064

Broughton, W R; Lodeiro, M J; Maudgal, S (2000) Accelerated test methods for assessing environmental degradation of composite laminates. NPL Report. CMMT(A)251

Broughton, W R; Lodeiro, M J; Maudgal, S (1999) Environmental degradation of unidirectional polmer matrix composites: an interim report. NPL Report. CMMT(A)187

Broughton, W R; Lodeiro, M J; Mulligan, D R (2000) Environmental degradation of undirectional composites. NPL Report. CMMT(A)250

Broughton, W R; Lodeiro, M J; Pilkington, G D (2010) Influence of coupling agents on material behaviour of glass flake reinforced polypropylene. Compos. A, Appl. Sci. Manuf., 41 (4). pp. 506-514.

Broughton, W R; Mera, R D; Hinopoulos, G (1999) Environmental degradation of adhesive joints: single-lap joint geometry. NPL Report. CMMT(A)196

Broughton, W R; Nimmo, W; Sims, G D (1995) Flexural failure of composite beam structures. In: Proc. 3rd Int. Conf. Deformation and fracture of composites, March 1995, University of Surrey.

Broughton, W R; Sims, G D (2009) Testing and evaluation of polymer composites. In: ICE Manual of Construction Materials. UNSPECIFIED, pp. 633-640. ISBN 9780727735973

Broughton, W R; Sims, G D (1994) An overview of through-thickness test methods for polymer matrix composites. NPL Report. DMM(A)148

C

Crocker, L E; Duncan, B C; Broughton, W R (2016) Assessment of test methods for a cryogenic liquid containment system. Int. J. Adhes. Adhes., 70. pp. 126-136.

D

Davies, A*; Foreman, A*; Shaw, R M; Sims, G D (2001) Fibre reinforced plastic composites - machining of composites and specimen preparation. Measurement Good Practice Guide. 38

Dean, G D; Mera, R D (2004) Determination of material properties and parameters required for the simulation of impact performance of plastics using finite element analysis. NPL Report. DEPC-MPR 007

Dent, A C E*; Bowen, C R*; Stevens, R*; Cain, M G; Stewart, M (2008) Tensile strength of active fibre composites - prediction and measurement. Ferroelectronics, 368 (1). pp. 209-215.

Domun, N; Kaboglu, C; Paton, K R; Dear, J P; Liu, J; Blackman, B R K; Liaghat, G; Hadavinia, H (2019) Ballistic impact behaviour of glass fibre reinforced polymer composite with 1D/2D nanomodified epoxy matrices. Composites Part B: Engineering, 167. pp. 497-506. ISSN 13598368

Domun, N; Paton, K R; Blackman, B R K; Kaboglu, C; Vahid, S; Zhang, T; Dear, J P; Kinloch, A J; Hadavinia, H (2020) On the extent of fracture toughness transfer from 1D/2D nanomodified epoxy matrices to glass fibre composites. Journal of Materials Science, 55 (11). pp. 4717-4733. ISSN 0022-2461

Domun, N; Paton, K R; Hadavinia, H; Sainsbury, T; Zhang, T; Mohamud, H (2017) Enhancement of fracture toughness of epoxy nanocomposites by combing nanotubes and nanosheets as filters. Materials, 10 (10). 1179

Domun, N*; Hadavinia, H*; Zhang, T*; Sainsbury, T; Liaghat, G H*; Vahid, S* (2015) Improving the fracture toughness and the strength of epoxy using nanomaterials - a review of the current status. Nanoscale, 7 (23). pp. 10294-10329.

G

Giannis, S; Adams, R D (2019) Failure of elastomeric sealants under tension and shear: Experiments and analysis. International Journal of Adhesion and Adhesives, 91. pp. 77-91. ISSN 01437496

Gower, M R L (2009) Project ACLAIM (Advanced Composite Life Assessment and Integrity Management): measurement of Mode I and II fracture toughness for mixed material systems used in ACLAIM case studies. NPL Report. MAT 19

Gower, M R L; Shaw, R M (2011) Development of test methods for measuring thick section tensile and compression properties of polymer matrix composites. NPL Report. MN 6

Gower, M R L; Shaw, R M (2009) Towards a planar cruciform specimen for biaxial characterisation of polymer matrix composites (PMCs). NPL Report. MN 9

Gower, M R L; Shaw, R M; Broughton, W R (2008) Thick Composites: Part I:Mechanical Test Review, Part II: Cure Optimisation. NPL Report. MAT 24

Gower, M R L; Shaw, R M; Wright, L; Urquhart, J; Hughes, J; Gnaniah, S; Morrell, R; Garstka, T* (2016) Determination of ply level residual stresses in a laminated carbon fibre-reinforced epoxy composite using constant, linear and quadratic variations of the incremental slitting method. Compos. A, Appl. Sci. Manuf., 90. pp. 441-450.

Gower, M R L; Sims, G D (2005) Characterisation of defects in composites materials systems. NPL Report. MATC(A)158

Gower, M R L; Sims, G D (1999) Determining the skin-to-core bond strength of sandwich constructions. NPL Report. CMMT(MN)044

Gower, M R L; Sims, G D (2003) Fibre-reinforced plastic composites - qualification of composite materials. Measurement Good Practice Guide. 64

Gower, M R L; Sims, G D (2003) Material data requirements and recommended test methods for the predictive modelling of defect criticality in composite material systems. NPL Report. MATC(A)147

Gower, M R L; Sims, G D (2003) Towards a Standard Qualification Plan (SQP) for composite materials - current status of material property databases. NPL Report. MATC(A)115

Gower, M R L; Sims, G D (2002) Towards a Standard Qualification plan (SQP) for composite materials - initial draft. NPL Report. MATC(A)84

Griffiths, A J; Turnbull, A (1994) An investigation of the electrochemical polarisation behaviour of 6061 A1 metal matrix composites. Corros. Sci., 36 (1). 23 - 35

H

Hajikazemi, M; McCarthy, L N; Paepegem, W; Sadr, M H (2018) Theory of Variational Stress Transfer in General Symmetric Composite Laminates Containing Non-Uniformly Spaced Ply Cracks. Composites Part A - Applied Science and Manufacturing, 107. pp. 374-386.

Hajikazemi, M; McCarthy, LN (2018) Comparison of Variational and Generalized Plane Strain approaches for matrix cracking in general symmetric laminates. International Journal of Damage Mechanics, 27 (4). pp. 507-540.

Harrer, W*; Morrell, R; Danzer, R* (2014) Fractography of biaxial tested Si3N4-specimens. J. Eur. Ceram. Soc., 34 (14). pp. 3283-3289.

Huang, E W*; Qiao, J W*; Winiarski, B; Lee, W J*; Scheel, M*; Chuang, C P*; Liaw, P K*; Lo, Y C*; Zhang, Y*; Di Michiel, M* (2014) Microyielding of core-shell crystal dendrites in a bulk-metallic-glass matrix composite. Scientific Reports, 4. p. 4394.

J

Jiang, L D*; Spearing, S M*; Monclus, M A; Jennett, N M (2011) Formation and mechanical characterisation of SU8 composite film reinforced with horizontally aligned and high volume fraction CNTs. Comp. Sci. Technol., 71 (10). pp. 1301-1308.

K

Katerelos, D G*; McCartney, L N; Galiotis, C* (2005) Local strain re-distribution and stiffness degradation cross-ply polymer composites under tension. Acta. Mater., 53. pp. 3335-3343.

Katerelos, D G*; McCartney, L N; Galiotis, C* (2005) Local strain re-distribution and stiffness degradation in cross-ply polymer composites under tension. Acta. Mater., 53. pp. 3335-3343.

Koukoulas, T; Broughton, W R; Tedaldi, M; Theobald, P D (2011) Novel non-contact optical characterisation methods of polymeric nanocomposite structures based on their particle loading and dispersion profile. Proc. SPIE - Int. Soc. Opt. Eng., 8082. 808220

Koukoulas, T; Broughton, W R; Theobald, P D; Tedaldi, M (2010) Characterization of solid complex multiphase systems based on oscillatory photon correlation spectroscopy. Opt. Lett., 35 (22). pp. 3754-3756.

Koukoulas, T; Broughton, W R; Williams, J*; Rahatekar, S* (2012) Optical characterisation of polymeric nanocomposites using tomographic, spectroscopic and Fraunhofer wavefront assessment. Proc. SPIE - Int. Soc. Opt. Eng., 8550. 855039

L

Lesniarek-Hamid, J L; Sims, G D (1993) Standardisation requirements for ultrasonic c-scanning of polymer matrix composites - an initial assessment. NPL Report. DMM(A)105

Lodeiro, M J; Maudgal, S; McCartney, L N; Morrell, R; Roebuck, B (1998) Critical review of interface testing methods for composites. NPL Report. CMMT(A)101

Lodeiro, M J; Young, T; Gower, M R L (2013) Feasibility of moisture and humidity determination using optical fibre sensing in polymer matrix composites. NPL Report. MN 11

Lord, J D (2004) Measuring the Poissin's ratio of fibre reinforced metal composites. NPL Report. DEPC-MN 008

Lord, J D (1997) Measuring the dimensional stability of composites. NPL Report. CMMT(MN)014

Lord, J D; Morrell, R (2014) Comparison of static and dynamic methods for measuring stiffness of high modulus steels and metal composites. Can. Metall. Q., 53 (3). pp. 292-299.

Lord, J D; Mummery, P M (1998) Review of elevated temperature fatigue life test methods for metal matrix composites. Project CPD2 - report 3- life assessment and prediction. NPL Report. CMMT(A)108

M

Maierhofer, C; Krankenhagen, R; Röllig, M; Rehmer, B; Gower, M; Baker, G; Lodeiro, M; Aktas, A; Monte, C; Adibekyan, A; Gutschwager, B (2018) Defect characterisation of tensile loaded CFRP and GFRP laminates used in energy applications by means of infrared thermography. Quantitative InfraRed Thermography Journal, 15 (1). pp. 17-36. ISSN 1768-6733

Maierhofer, C; Krankenhagen, R; Röllig, M; Unnikrishnakurup, S; Monte, C; Adibekyan, A; Gutschwager, B; Knazowicka, L; Blahut, A; Gower, M; Lodeiro, M; Baker, G; Aktas, A (2018) Influence of thermal and optical material properties on the characterization of defects in fiber reinforced composites with active thermography methods. tm - Technisches Messen, 85 (1). pp. 13-27. ISSN 0171-8096

Maierhofer, C; Röllig, M; Gower, M; Lodeiro, M; Baker, G; Monte, C; Adibekyan, A; Gutschwager, B; Knazowicka, L; Blahut, A (2018) Evaluation of Different Techniques of Active Thermography for Quantification of Artificial Defects in Fiber-Reinforced Composites Using Thermal and Phase Contrast Data Analysis. International Journal of Thermophysics, 39 (5). 61 ISSN 0195-928X

Maierhofer, C*; Krankenhagen, R*; Rollig, M*; Rehmer, B*; Gower, M; Baker, G; Lodeiro, M; Aktas, A; Knazovicka, L*; Blahut, A*; Monte, C*; Adibekyan, A*; Gutschwager, B* (2016) Characterisation of artificial defects in CFRP and GFRP sheets designed for energy applications using active thermography. In: 13th Quantitative Infrared Thermography Conference, 4-8 July 2016, Gdansk, Poland.

Maxwell, A S; Broughton, W R; Lodeiro, M J; Shaw, R (2009) Measurement of residual stresses and strains in carbon fibre composites. NPL Report. MN 7

May, D.; Aktas, A.; Advani, S.G.; Berg, D.C.; Endruweit, A.; Fauster, E.; Lomov, S.V.; Long, A.; Mitschang, P.; Abaimov, S.; Abliz, D.; Akhatov, I.; Ali, M.A.; Allen, T.D.; Bickerton, S.; Bodaghi, M.; Caglar, B.; Caglar, H.; Chiminelli, A.; Correia, N.; Cosson, B.; Danzi, M.; Dittmann, J.; Ermanni, P.; Francucci, G.; George, A.; Grishaev, V.; Hancioglu, M.; Kabachi, M.A.; Kind, K.; Deléglise-Lagardère, M.; Laspalas, M.; Lebedev, O.V.; Lizaranzu, M.; Liotier, P.-J.; Middendorf, P.; Morán, J.; Park, C.-H.; Pipes, R.B.; Pucci, M.F.; Raynal, J.; Rodriguez, E.S.; Schledjewski, R.; Schubnel, R.; Sharp, N.; Sims, G.; Sozer, E.M.; Sousa, P.; Thomas, J.; Umer, R.; Wijaya, W.; Willenbacher, B.; Yong, A.; Zaremba, S.; Ziegmann, G. (2019) In-plane permeability characterization of engineering textiles based on radial flow experiments: A benchmark exercise. Composites Part A: Applied Science and Manufacturing, 121. pp. 100-114. ISSN 1359835X

McCartney, L N (1993) Analytical micromechanical models for the prediction of multiple cracking in composites. J. Phys. IV Colloq., 3 (C7). pp. 1637-1646.

McCartney, L N (2013) Analytical model for sliding interfaces associated with fibre fractures or matrix cracks. Comp. Mater. Continua, 35 (3). pp. 183-227.

McCartney, L N (2013) Analytical models for sliding interfaces associated with fibre fractures or matrix cracks. CMC - Comput. Mater. Cont., 35 (3). pp. 183-227.

McCartney, L N (2013) Derivations of energy-based modelling for ply cracking in general symmetric laminates. J. Compos. Mater., 47 (20-21). pp. 2641-2673.

McCartney, L N (1997) Design guide for predicting composite properties. part i: description of methodology. NPL Report. CMMT(A)79

McCartney, L N (2004) Effect of mixed mode loading on ply crack development in laminated composites: theory and application. NPL Report. MATC(A)167

McCartney, L N (2008) Energy methods for fatigue damage modelling of laminates. Comp. Sci. Technol., 68 (13). pp. 2601-2615.

McCartney, L N (2013) Energy methods for modelling damage in laminates. J. Compos. Mater., 47 (20-21). pp. 2613-2640.

McCartney, L N (1995) Interaction of transverse cracks of finite size in a cross-ply laminate. In: Proc. 10th International conference on Composite Materials, 14-18 August 1995, Whistler, B.C., Canada.

McCartney, L N (2010) Maxwell's far-field methodology predicting elastic properties of multi-phase composites reinforced with aligned transverse isotropic spheroids. Philos. Mag., 90 (31-32). pp. 4175-4207.

McCartney, L N (1992) Mechanics for the growth of bridge cracks in composite materials II. Applications. J. Compos. Technol. Res., 14 (3). pp. 147-154.

McCartney, L N (1992) Mechanics for the growth of bridged cracks in composite materials I. Basic principles. J. Compos. Technol. Res., 14 (3). pp. 133-146.

McCartney, L N (1998) Model of composite degradation due to environmental damge. NPL Report. CMMT(A)124

McCartney, L N (2001) Model of composite degradation due to environmentally assisted fatigue damage. NPL Report. MATC(A)26

McCartney, L N (1999) Model of composite degradation due to fatigue damage. NPL Report. CMMT(A)211

McCartney, L N (2003) Physically based damage models for laminated composites. I Mech. E. J. of Materials: Design & Applications, 217. pp. 163-199.

McCartney, L N (1995) Prediction of microcracking in composite materials. In: Cherepanov, G P, ed., Fracture: a topical encyclopaedia of current knowledge dedicated to Alan Arnold Griffith. Melbourne. USA: Krieger Publishing Co., pp. 905-916.

McCartney, L N (1997) Should composite micro-mechanics be used in design? In: Proc. 4th International Conference on Composite Engineering, July 1997, Hawaii, USA.

McCartney, L N (2001) Simulation of progressive damage formation and failure during the loading of cross-ply composites. NPL Report. MATC(A)20

McCartney, L N (1999) Simulation of progressive fibre failure during the tensile loading of unidirectional composites. NPL Report. CMMT(A)212

McCartney, L N (1996) Stress transfer mechanics for angle-ply laminates. In: ECCM-7 7th European Conference on Composite Materials, 14 - 16 May 1996, London, UK.

McCartney, L N (1993) Stress transfer mechanics for multiple perfectly bonded concentric cylinder models of unidirectional composites. NPL Report. DMM(A)129

McCartney, L N (1996) Stress transfer mechanics for ply cracks in general symmetric laminates. NPL Report. CMMT(A)50

McCartney, L N (1993) The prediction of cracking in biaxially loaded cross-ply laminates having brittle matrices. Composites, 24 (2). pp. 84-92.

McCartney, L N; Blazquez, A*; Paris, F* (2012) Energy-based delamination theory for biaxial loading in the presence of thermal stresses. Comp. Sci. Technol., 72 (14). pp. 1753-1766.

McCartney, L N; Hannaby, S A; Cooper, P M (1995) Effects of cracking in multi-ply cross-ply laminates. In: Proc. 3rd Int. Conf. Deformation and fracture of composites, March 1995, University of Surrey.

McCartney, L N; Kelly, A* (2007) Effective thermal and elastic properties of [+theta /-theta ]s laminates. Comp. Sci. Technol., 67. pp. 646-661.

McCartney, L N; Kelly, A* (2008) Maxwell's far-field methodology applied to the prediction of properties of multi-phase isotropic particulate composites. Proc. R. Soc. Lond. A, 464 (2090). pp. 423-446.

McCartney, L N; Pierse, C (1997) Stress transfer mechanics for multiple ply laminates for axial loading and bending. In: Proc. 11th International Conference on Composite Materials, July 1997, Gold Coast, Australia.

McCartney, L N; Pierse, C (1997) Stress transfer mechanics for multiple ply laminates subject to bending. NPL Report. CMMT(A)55

McCormick, N J; Gower, M R L; McCartney, L N (2002) An Internet accessible system for simulating damage in composite laminates during bending deformation. NPL Report. MATC(A)96

Mendels, D A; Shaw, R M (2002) Determination of mode I energy release rate in composite laminates by the wedge test. NPL Report. MATC(MN)36

Mendels, D A; Shaw, R M (2002) Determination of mode II energy release rate in composite laminates by the modified double-lap shear test. NPL Report. MATC(A)125

Mera, R D; Sims, G D (2001) Opportunities for composites in the energy industry. NPL Report. MATC(A)64

Morrell, R; McCartney, L N (1993) Measurement of properties of brittle matrix composites. Br. Ceram. Trans. J., 92 (1). pp. 1-7.

Mulligan, D R; Gnaniah, S J P; Sims, G D (2003) Thermal analysis techniques for composites and adhesives (second edition). Measurement Good Practice Guide. 62

Mulligan, D R; Gnaniah, S J P; Sims, G D (2000) Thermal analysis techniques for composites and adhesives. Measurement Good Practice Guide. 32

Mulligan, D R; Sims, G D (1999) Characterisation of fibre surfaces by wetting techniques. NPL Report. CMMT(MN)055

Mulligan, D R; Sims, G D (2000) Test methods for chemical and physical characterisation of the fibre-matrix interface in composite materials. NPL Report. CMMT(MN)65

Munz, M (2008) On the nature of the multi-zone interphase of a thermoset/thermoplastic composite - an analysis employing dynamic-mechanical thermal analysis and nanoindentation. J. Adhes., 84 (5). pp. 445-482.

N

Nelson, L J*; Bowen, C R*; Stevens, R*; Cain, M G; Stewart, M (2003) High field behaviour of piezoelectric fibre composites. Proc. SPIE - Int. Soc. Opt. Eng., 5053. pp. 544-555.

Niklewicz, J; Sims, G D (2002) Size effects in composite materials. NPL Report. MATC(A)74

P

Palaniappan, J*; Wang, H*; Ogin, S L*; Thorne, A*; Reed, G T*; Tjin, S C*; McCartney, L N (2006) Prediction of the reflected spectra from chirped fibre Bragg gratings embedded within cracked crossply laminates. Meas. Sci. Technol., 17. pp. 1609-1614.

Parsons, S; Murphy, R J*; Lee, J*; Sims, G D (2015) Uncertainty communication in the environmental life cycle assessment of carbon nanotubes. Int. J. Nanotechnol., 12 (8-9). pp. 620-630.

R

Robinson, D W*; Wright, J*; Gupta, S*; Mottram, T*; Armitage, P*; Gower, M R L; Lodeiro, M J; Gelat, P N; Schwarz, C* (2016) A novel non-linear elastic wave acoustic spectroscopy (NEWS) non-destructive inspection (NDI) method for aeronautic and spacecraft materials and components. CEAS Space J., 8 (1). pp. 35-45.

Roebuck, B (2001) Miniature testpiece for the assessment of the dimensional stability of monolithic and metal composite aluminium alloys. NPL Report. CMMT(MN)069

Roebuck, B; Gee, M G; Lord, J D; McCartney, L N (1998) Miniature thermal cycling tests on aluminium alloy metal matrix composites. Mater. Sci. Technol., 14 (Sept -). pp. 1001-1008.

Roebuck, B; Lord, J D (1993) Particulate metal matrix composites - draft procedure for tensile tests at ambient temperature. NPL Report. DMM(A)100

Roebuck, B; Lord, J D (1996) Standardisation of high temperature tensile tests for discontinuously reinforced metal matrix composites. NPL Report. CMMT(MN)002

Roebuck, B; Lord, J D; Orkney, L P (1994) Compression testing of metal matrix composites. In: ECCM CTS 2 (Testing and Standardisation) European Conference, 13-15 September 1994, Hamburg, Germany.

S

Saavedra, M S; Sims, G D; McCartney, L N; Stolojan, V*; Anguita, J V*; Tan, Y Y*; Ogin, S L*; Smith, P A*; Silva, S R P* (2012) Catalysing the production of multiple arm carbon octopi nanostructures. Carbon, 50 (6). pp. 2141-2146.

Sanderson, A R*; Ogin, S L*; Crocombe, A D*; Gower, M R L; Lee, R J* (2012) Use of surface-mounted chirped fibre Bragg grating sensor to monitor delamination growth in a double-cantilever beam test. Comp. Sci. Technol., 72 (10). pp. 1121-1126.

Seah, M P; Hunt, C P; Sykes, D*; Valeri, S*; Muller, R*; Lamb, B* (1993) Interlaboratory tests of a composite reference sample to calibrate Auger electron spectrometers in the differential mode. J. Electron Spectrosc. Relat. Phenom., 61 (2). pp. 173-182.

Shaw, R M; Sims, G D (2004) Through-thickness tensile testing of polymer matrix composites. NPL Report. DEPC-MN 007

Shaw, R M; Sims, G D (2005) Understanding compression testing of thick polymer matrix composites. NPL Report. DEPC-MN 019

Sim, G D; Bennett, S (2007) VAMAS promotes metrology of material property measurement at CIPM. MAPAN, J. Metrol. Soc. India, 22 (3). pp. 209-220.

Sims, G D (2002) Annual review of composites standardisation activities, April 2001-March 2002. NPL Report. MATC(A)110

Sims, G D (1997) Composite test methods standardisation: trends and issues. NPL Report. CMMT(A)85

Sims, G D (1995) European standardisation for composites: test methods, materials, vessels, tanks and pipework. In: FRC II -Tanks and vessels. I Mech Eng..

Sims, G D (1994) International standardisation of coupon and structural element test methods. In: ECCM CTS - 2nd European Conference on Composites Testing and Standardisation, September 1994, Hamburg, Germany.

Sims, G D (2002) Polymer Composites. VAMAS Bulletin, 25. pp. 29-31.

Sims, G D (2001) Polymer composites. VAMAS Bulletin, 24. pp. 31-32.

Sims, G D (2003) Review of composites standardisation activities, April 2002 - March 2003. NPL Report. MATC(A)151

Sims, G D (1998) Standards will cut composites industry costs. Reinforced Plastics, 42 (8). 54-55, 57-58

Sims, G D (2002) Traceability and qualification in design with composite materials. NPL Report. MATC(A)81

Sims, G D; Broughton, W R (2000) Glass fiber reinforced plastics - properties. In: Comprehensive Composite Materials. Elsevier, pp. 151-197.

Sims, G D; Gnaniah, S J P (2005) Polymer composites - rate dependent temperature calibration of dynamic mechanical analysers (DMA) for Tg measurements. NPL Report. DEPC-MN 017

Sims, G D; Nimmo, W; Johnson, A F; Ferriss, D H (1994) Analysis of plate-twist test plane shear modulus of composite materials. NPL Report. DMM(A)54

Sims, G D; Payne, D R; Ferriss, D H (1996) Analysis and experimental validation of structural element test methods. In: ECCM-7 7th European Conference on Composite Materials, 14-16 May 1996, London, UK.

Sims, G D; Saveedra, M (2010) An introduction to the properties of carbon nano-particle enhanced polymers. NPL Report. MN 10

U

Utracki, L A; Broughton, W R; Gonzalez-Rojano, N*; de Carvalho, L H*; Achete, C A* (2011) Clays for polymeric nanocomposites. Polym. Eng. Sci., 51 (3). pp. 559-572.

W

Williams, J*; Broughton, W R; Koukoulas, T; Rahatekar, S S* (2013) Plasma treatment as a method for functionalising and improving dispersion of carbon nanotubes in epoxy resins. J. Mater. Sci., 48 (3). pp. 1005-1013.

Y

Young, T J; Crocker, L E; Broughton, W R; Ogin, S L*; Smith, P A* (2013) Observations on interphase characterisation in polymer composites by nano-scale indentation using AFM and FEA. Compos. A, Appl. Sci. Manuf., 50. pp. 39-43.

Young, T J; Lodeiro, M J; Gower, M R L; Sassi, M B (2013) Systematic approach for the calibration of humidity sensitive polyimide recoated fibre Bragg gratings for measuring humidity and temperature and the application for measuring moisture absorption in polymers. Meas. Sci. Technol., 24 (8). 085101

Young, T J; Monclus, M A; Broughton, W R; Ogin, S L*; Smith, P A* (2012) Observations on interphase characterisation in polymer composites by nanoscale indentation and use of AFM cantilever torsion to identify measurement artefacts. Plast. Rubber Compos., 41 (6). pp. 240-246.

Young, T J; Monclus, M A; Burnett, T L; Broughton, W R; Ogin, S L*; Smith, P A* (2011) The use of the PeakForce quantitative nanomechanical mapping AFM-based method for high-resolution Young's modulus measurement of polymers. Meas. Sci. Technol., 22 (12). 125703

This list was generated on Wed Aug 12 16:28:35 2020 BST.