A

Aktas, A; Potluri, P* (2015) Needle penetration through polymeric cellular foam materials. Mech. Adv. Mater. Struct., 22 (10). pp. 794-802.

Allen, C R G; Tomlins, P E (1999) The influence of shear history on the crystallization behaviour of talc filled polypropylenes. NPL Report. CMMT(A)182

Allen, P*; Butler, B P; Cook, H R; Lord, G J; Pardo, E; Smith, I M; Tomlins, P E (1999) The influence of processing conditions on the dimensional stability of pigmented mouldings. NPL Report. CMMT(A)194

Arranz, E; Brown, C S; Gnaniah, S J P; Percio, S (2001) Latent heat of polymers crystallised under pressure. NPL Report. MATC(A)44

B

Breuer, H*; Dean, G; Tiba, H*; Shastri, R* (1994) International standards for the acquisition and presentation of comparable data on plastics. In: Proc. SPE Challenging the status quo in design, 1994.

Broughton, B; Maxwell, T (2022) Accelerated Life Testing and Ageing. In: ASM Handbook 11B: Characterization and Failure Analysis of Plastics. ASM International. ISBN 9781627083959

Broughton, W R (2001) Analytical models for assessing environmental degradation of unidirectional and cross-ply laminates. NPL Report. MATC(A)1

Broughton, W R (1999) Project PAJ3 - Combined cyclic loading and hostile environments 1996-1999. Report no 19. Project PAJ3: final report. NPL Report. CMMT(A)237

Broughton, W R; Koukoulas, T; Woolliams, P D (2016) Assessment of nanoparticle loading and dispersion in polymeric materials using oscillatory photon correlation spectroscopy. Polym. Test., 49. pp. 107-114.

Broughton, W R; Lodeiro, M J (2000) Cyclic fatigue of continuous unidirectional polymer matrix composites. NPL Report. CMMT(A)249

Broughton, W R; Lodeiro, M J (1999) Cyclic fatigue of continuous unidirectional polymer matrix composites: an interim report. NPL Report. CMMT(A)186

Broughton, W R; Lodeiro, M J; Maudgal, A; Sims, G D (1998) Review of test methods and standards for assessing long-term performance of polymer matrix composites. NPL Report. CMMT(A)94

Broughton, W R; Maxwell, A S (2023) Accelerated ageing of polymeric materials. Measurement Good Practice Guide. 103 (Issue 2)

Broughton, W R; Mera, R D (1997) Project PAJ3 combined cyclic loading and hostile environments 1996-1999. Report No. 1, Review of durability test methods and standards for assessing long term performance of adhesive joints. NPL Report. CMMT(A)61

Broughton, W R; Mera, R D (1997) Project PAJ3 combined cyclic loading and hostile environments 1996-1999. Report No.2: review of life prediction methodology and adhesive joint design and analysis software. NPL Report. CMMT(A)62

Broughton, W R; Pilkington, G D; Ratnakela, D K (2007) Accelerated weathering: performance testing of polymer matrix composites. NPL Report. DEPC-MN 047

Broughton, W R; Sims, G D (1994) An overview of through-thickness test methods for polymer matrix composites. NPL Report. DMM(A)148

Brown, C S; Hobbs, C (1998) Pressure-volume-temperature behaviour of polymers during rapid cooling. NPL Report. CMMT(MN)033

Brown, C S; Hobbs, C B; Spitteler, P (2000) Monitoring processing of reactive polymer systems using ultrasonics. NPL Report. CMMT(A)261

Brown, C S; Hobbs, C B; Spitteler, P H J (2000) Ultrasonic monitoring of reactive polymer processing. NPL Report. CMMT(MN)059

C

Cavasin, M; Sangermano, M; Thomson, B; Giannis, S (2019) Exposure of Glass Fiber Reinforced Polymer Composites in Seawater and the Effect on Their Physical Performance. Materials, 12 (5). 807 ISSN 1996-1944

Chakravorty, S (1999) Specification of pressure-volume-temperature (PVT) measurements relevant to industrial polymer processing. NPL Report. CMMT(A)244

Chakravorty, S (2002) An assessment of polymer nano-composite materials. NPL Report. MATC(A)123

Chakravorty, S (1999) A review of requirements for improved methods of measuring thermal properties of polymer. NPL Report. CMMT(A)246

Chakravorty, S; Rides, M; Allen, C R G; Brown, C S (1996) Polymer melt viscosity increases under pressure - a simple new measurement method. Plast. Rubber Compos. Process. Appl., 25 (5). pp. 260-261.

Chakravorty, S; Rides, M; Allen, C R G; Brown, C S (1996) The pressure dependency of the shear viscosity of polymer melts: an international round robin study. NPL Report. CMMT(A)7

Charalambides, M N; Dean, G (1997) Project PAJ2, dynamic performance of adhesively bonded joints. Report No 2 April 1997, constitutive models and their data requirements for use in finite analysis of adhesives under impact loading. NPL Report. CMMT(A)59

Cook, A; Dawson, D; Duncan, B C (1993) Measurement and modelling of bolted joint stress relaxation in plastics. NPL Report. DMM(A)109

Cumpson, P J (2001) Estimation of inelastic mean free paths for polymers and other organic materials: use of quantitative structure-property relationships. Surf. Interface Anal., 31. pp. 23-34.

D

Dawson, A; Maxwell, A S (2015) Towards a quantitative methodology for measuring micro and nanoscale transition properties for heat transfer modelling in thermal devices and materials. In: 21st International Workshop on Thermal Investigations of ICs and Systems (THERMINIC), 30 September - 2 October 2015, Paris, France.

Dawson, A; McCalla, B*; Brown, C S; Mulligan, D R; Crocker, L E (2003) The consequences of rapid processing techniques on the physical properties of plastics components. NPL Report. MATC(A)150

Dawson, A; Rides, M; Cuenat, A; Winkless, L (2013) Micro and nano-scale measurement of the thermophysical properties of polymeric materials using atomic force microscopy. Int. J. Thermophysics, 34 (5). pp. 865-882.

Dawson, A; Rides, M; Maxwell, A S; Cuenat, A; Samano, A R (2015) Scanning thermal microscopy techniques for polymeric thin films using temperature contrast mode to measure thermal diffusivity and a novel approach in conductivity contrast mode to the mapping of thermally conductive particles. Polym. Test., 41. pp. 198-208.

Dean, G (1997) Design data for plastics for finite element analysis. In: Proc. Polymer Testing Conference 97, April 1997, Shawbury, Shropshire.

Dean, G (1995) International standards for comparable data for plastics. NPL Report. DMM(A)166

Dean, G; Charalambides, M N (1997) Project CAM6. Development of test methods for design under high rates of loading. Report No. 1 April 1997 - Data requirements for the use of finite element methods to predict the impact performance of plastics. NPL Report. CMMT(A)58

Dean, G; Crocker, L E (1999) Project PAJ2. Report No 10. A proposed failure criterion for tough adhesives. NPL Report. CMMT(A)158

Dean, G; Hu, F; Duncan, B C (1998) Project PAJ2, Report No. 5. The application of finite element methods to the design of adhesive joints. NPL Report. CMMT(A)102

Dean, G; Hunt, R A; Shastri, R* (2000) Illustrations of the application of finite element and processing simulation analyses to plastics. NPL Report. CMMT(A)266

Dean, G; Mera, R D; Arranz, E (2002) Determination of the properties of plastics at high strain rates. NPL Report. MATC(A)116

Dean, G; Read, B E; Duncan, B C (1998) Project CAM6, Report No. 3. The application of finite element methods to the prediction of the impact performance of plastics. NPL Report. CMMT(A)100

Dean, G; Read, B E; Duncan, B C (1999) Project PAJ2, Report No. 7, An evaluation of yield criteria for adhesives for finite element analysis. NPL Report. CMMT(A)117

Dean, G; Shastri, R*; Lockett, F J* (1997) Project CAM6, Report No.2, ISO guide to the acquisition and presentation of design data for plastics. NPL Report. CMMT(A)82

Dean, G; Wright, L (2002) Comparison of the measured and predicted deformation of a circular plate of an ABS polymer used under centre loading. NPL Report. MATC(A)105

Dean, G; Wright, L (2000) Deformation of a centrally loaded circular plate of a thermoplastic material: comparison of measurements with predictions using finite element analysis. NPL Report. CMMT(A)299

Dean, G; Wright, L (2003) An evaluation of the use of finite element analysis for predicting the deformation of plastics under impact loading. Polym. Test., 22 (6). pp. 625-631.

Dean, G D (2011) Modelling and analysis of creep data for plastics at elevated temperatures. Polym. Test., 30 (2). pp. 229-235.

Dean, G D; Crocker, L E (2006) Prediction of the impact performance of plastics mouldings. NPL Report. DEPC-MPR 043

Dean, G D; Crocker, L E (2022) Prediction of the impact performance of plastics using finite element methods. Measurement Good Practice Guide. 87 (Issue 2)

Dean, G D; McCartney, L N; Mera, R D; Urquhart, J M (2011) Modelling non-linear viscoelasticity in polymers for design using finite element analysis. Polym. Eng. Sci., 51 (11). pp. 2210-2219.

Dean, G D; Mera, R D (2005) Measurement of failure in tough plastics at high strain rates. NPL Report. DEPC-MN 028

Dean, G D; Shastri, R* (2000) Committee draft for an ISO guide to the acquisition and presentation of design data for plastics. NPL Report. CMMT(A)256

Dean, G D; Tomlins, P E; Read, B E (1993) A model for non-linear creep and physical ageing in PVC. NPL Report. DMM(A)91

Dean, G D; Tomlins, P E; Read, B E (1995) A model for nonlinear creep and physical ageing in poly vinyl chloride. Polym. Eng. Sci., 35 (16). pp. 1282-1289.

Dean, G D; Tomlins, P E; Read, B E (1995) A model for nonlinear creep and physical aging in poly(vinyl chloride). Polm. Eng. Sci., 35 (16). pp. 1282-1289.

Duncan, B C (1999) Comparison between rheological and bulk specimen tests for creep and stress relaxation properties. NPL Report. CMMT(A)184

Duncan, B C (1999) Project PAJ1: final report. NPL Report. CMMT(A)232

Duncan, B C (1998) Project PAJ2: Report No. 6, Project CAM6: Report No. 4. NPL Report. CMMT(A)109

Duncan, B C; Broughton, W R (2023) Absorption and diffusion of moisture in polymeric materials. Measurement Good Practice Guide. 102 (Issue 2)

Duncan, B C; Pearce, A (1999) Comparison of impact and high rate tests for determining properties of adhesives and polymers needed for design under impact loading. NPL Report. CMMT(A)134

Duncan, B C; Urquhart, J M; Roberts, S (2005) Review of measurement and modelling of permeation and diffusion in polymers. NPL Report. DEPC-MPR 012

F

Fernandez-Cuesta, I*; Borrise, X*; Retolaza, A*; Merino, S*; Mendels, D A; Hansen, O*; Kristensen, A*; Perez-Murano, F* (2008) Determination of stress build-up during nanoimprint process in triangular polymer structures. Microelectron. Eng., 85 (5-6). pp. 838-841.

Fry, A; Monaghan, P; Rides, M (1999) Measurement of reactive polymer systems. NPL Report. CMMT(A)224

Fry, A T; Brown, C S (1999) Measurement methods relating to the processing of plastics: the measurement of reactive polymer systems. NPL Report. CMMT(MN)047

G

Gibbs, P A J (1994) Ultrasonic cure measurements during the processing of an unsaturated polyester dough moulding compound. British Plastics Federation Composite Congress, 293 (8). pp. 7-16.

Gibbs, P A J; Rides, M (1993) Modelling the inhibition cure behaviour of unsaturated polyester moulding materials. NPL Report. DMM(A)107

Gibbs, P A J; Rides, M (1995) Modelling the rheology of an unsaturated polyester moulding material during cure. NPL Report. DMM(A)164

Gibbs, P A J; Rides, M (1993) A technique to predict the curing behaviour of unsaturated polyester materials. NPL Report. DMM(A)120

Gibbs, P A J; Rides, M; Williamson, P* (1993) An ultrasonic measurement technique to determine the state of cure in thermosetting materials. NPL Report. DMM(A)114

H

Hobbs, C B; Brown, C S (1999) Pressure/Volume/Temperature (PVT) behaviour of polymers during ultrafast cooling. NPL Report. CMMT(A)163

Hou, X.D.; Jennett, N.M. (2018) Defining the limits to long-term nano-indentation creep measurement of viscoelastic materials. Polymer Testing, 70. pp. 297-309. ISSN 01429418

J

Juric, I; Tutis, E* (2014) Dark injection transient spectroscopy and density of states in amorphous organics. Organic Electronics, 15 (1). pp. 226-239.

K

Kandil, F A (1999) Potential ambiguity in the determination of the plastic strain range component in LCF testing. Int. J. Fatigue, 21 (10). pp. 1013-1018.

Kim, J S*; Wood, S; Shoaee, S*; Spencer, S J; Castro, F A; Tsoi, W C*; Murphy, C E; Sim, M*; Cho, K*; Durrant, J R*; Kim, J S* (2015) Morphology-performance relationships in polymer/fullerene blends probed by complementary characterisation techniques - effects of nanowire formation and subsequent thermal annealing. J. Mater. Chem. C, 3 (35). pp. 9224-9232.

Koukoulas, T; Broughton, W R; Woolliams, P D (2015) Assessment of nanoparticle loading and dispersion in polymeric materials using optical wavefront correlation. Polym. Test., 44. pp. 57-65.

L

Lodeiro, M J; Hobbs, C B (2003) Ultrasonic measurements for cure monitoring in polymeric material systems. NPL Report. MATC(MN)47

Lodeiro, M J; Tomlins, P E (2002) Influence of pigments and processing on the dimensions and appearance of HDPE injection-moulded bottle caps. NPL Report. MATC(MN)22

Lodeiro, M J; Tomlins, P E; Pearce, A (2000) The influence of pigments on the mechanical properties of High Density Polythylene (HDPE). NPL Report. CMMT(A)258

Lodeiro, M*; Broughton, W R; Sims, G D (1999) Understanding the limitations of through-thickness test methods. Plast. Rubber Compos., 28 (9). pp. 416-424.

M

Maxwell, A S (2005) Measurement of residual stress in plastics. NPL Report. DEPC-MN 027

Maxwell, A S (2005) Review of techniques for monitoring the environmental degradation of polymers. NPL Report. DEPC-MPR 015

Maxwell, A S (2008) Weathering of recycled photo-degraded polyethylene. Polm. Eng. Sci., 48 (2). pp. 381-385.

Maxwell, A S; Broughton, W R; Dean, G D; Sims, G D (2005) Review of accelerated ageing methods and lifetime prediction techniques for polymeric materials. NPL Report. DEPC-MPR 016

Maxwell, A S; Broughton, W R; Lodeiro, M J (2006) Review of techniques for the characterisation of residual stress in polymer composites. NPL Report. DEPC-MPR 056

Maxwell, A S; Monclus, M; Jennett, N M; Dean, G (2011) Accelerated testing of creep in polymeric materials using nanoindentation. Polym. Test., 30 (4). pp. 366-371.

Maxwell, A S; Pilkington, G (2008) Prediction of environmental stress cracking resistance in polyethylenes. Polym. Eng. Sci., 48 (2). pp. 360-364.

Maxwell, A S; Turnbull, A (2003) Chemical probe technique for assessing the susceptibility of polymeric mouldings to environmental stress cracking. Polym. Test., 22. pp. 259-265.

Maxwell, A S; Turnbull, A (2000) Environmental stress cracking of polymeric materials. NPL Report. CMMT(A)288

Maxwell, A S; Turnbull, A (2000) Influence of small fluctuating loads on environment stress cracking of polymers. In: Proceedings of Deformation, Yield and Fracture of Polymers, April 2000, Institute of Materials, Cambridge, UK.

Maxwell, A S; Turnbull, A (2004) Influence of small fluctuating loads on environment stress cracking of polymers. Polym. Test., 23. pp. 419-422.

Maxwell, A S; Turnbull, A (2003) Measurement of residual stress in engineering plastics using the hole-drilling technique. Polym. Test., 22. pp. 231-233.

Maxwell, A S; Turnbull, A (2000) Measurement of residual stress in polymeric materials. In: 6th International Conference on Residual Stress, July 2000, Institute of Materials, UK.

Maxwell, A S; Wang, Y W*; Tomlins, P E (2014) On the use of gamma radiation to change the characteristics of porous poly(caprolactone) tissue scaffolds. Int. J. Polym. Mater. Polym. Biomater., 63 (3). pp. 123-129.

Mendels, D A; Shaw, R M (2002) Detection of sub-surface defects in multi-layered polymer composites by speckle pattern interferometry. NPL Report. MATC(MN)17

Mera, R D; Duncan, B C (2005) Characterising the absorbency of porous substrates. NPL Report. DEPC-MN 015

Mulligan, D R; Brown, C S; Fry, A; Percio, S (2001) Effect of pressure on thermal conductivity of polymers. NPL Report. MATC(A)33

O

Olusanya, A (1997) Project PAJ3 combined cyclic loading and hostile environments 1996-1999. Report 3. A guide to the use of design of experiment methods. NPL Report. CMMT(A)67

Olusanya, A; Tully, K; Mera, R; Broughton, W R (1998) A comparison of commercial design of experimental software programs for the analysis of durability data. NPL Report. CMMT(A)98A

P

Pillai, S; Bull, C; Turnbull, A (1997) Measurement of environment stress cracking of plastics. In: Euromat 97, 21-23 April 1997, Maastricht, Netherlands.

R

Read, B E (1996) Generation of creep data for injection-moulded plastics. NPL Report. CMMT(A)24

Read, B E; Dean, G; Duncan, B C (1999) Project CAM6, Report No. 6. Characterisation of the strain rate and temperature dependence of the properties of plastics for the prediction of impact performance. NPL Report. CMMT(A)144

Read, B E; Dean, G; Duncan, B C (1998) Project CAM6. Report No. 5. Characterisation of the Non-linear behaviour of plastics for finite element analysis. NPL Report. CMMT(A)114

Read, B E; Dean, G; Duncan, B C (1999) Project PAJ2. Report No 11. Strain rate and temperature dependence of the properties of adhesives. Prediction of high rate data. NPL Report. CMMT(A)169

Read, B E; Dean, G; Tomlins, P E (1993) Creep and physical ageing of PVC: dependence on stress and temperature. NPL Report. DMM(A)115

Read, B E; Dean, G; Tomlins, P E (1994) Creep and physical ageing of PVC: dependence on stress and temperature. J. Non-Cryst. Solids, 172. 562 - 568

Read, B E; Dean, G; Wright, L (2002) Influence of strain rate and temperature on the stress/strain behaviour of rubber-toughened plastics. NPL Report. MATC(A)77

Read, B E; Dean, G D; Tomlins, P E (1993) Modelling of creep data for plastics. NPL Report. DMM(A)92

Read, B E; Dean, G D; Wright, L (2000) A proposed model for the non-linear stress/strain behaviour of rubber-toughened plastics. NPL Report. CMMT(A)301

Read, B E; Dean, G D; Wright, L* (2001) Effects of cavity growth and orientation hardening on the stress.strain behaviour of rubber-toughened plastics. NPL Report. MATC(A)35

Read, B E; Tomlins, P E (1996) Creep and physical ageing of injection moulded, fibre reinforced polypropylene. NPL Report. CMMT(A)21

Read, B E; Tomlins, P E (1994) Creep recovery of PVC and polypropylene. NPL Report. DMM(A)151

Read, B E; Tomlins, P E (1996) Time-dependent deformation of polypropylene in response to different stress histories. NPL Report. CMMT(A)16

Rides, M (2000) Determination of the uncertainties in transient extensional viscosity testing. NPL Report. CMMT(A)303

Rides, M (2000) Draft ISO standard for the determination of the transient extensional viscosity of polymer melts. NPL Report. CMMT(A)248

Rides, M (1996) Effect of pressure-volume-temperature behaviour of polymer melts on extrudate swell measurements. NPL Report. CMMT(A)13

Rides, M (1993) In-line measurement of shear viscosity using an injection moulding machine. NPL Report. DMM(A)141

Rides, M (1996) Numerical simulation of the extrudate swell behaviour of polymer melts. NPL Report. CMMT(A)31

Rides, M (1993) Numerical simulation of the flow of thermosetting plastics: application to injection moulding. NPL Report. DMM(A)123

Rides, M (2009) Review of methods for the characterisation of the dispersion in polymer nanocomposites. NPL Report. MAT 34

Rides, M (2007) The feel good factor. Plast. Eng. (March). pp. 46-49.

Rides, M; Allen, C R G (1996) Capillary extrusion rheometry intercomparison using polyethylene and glass-fibre filled polypropylene melts: measurement of shear viscosity and entrance pressure drop. NPL Report. CMMT(A)25

Rides, M; Allen, C R G (2001) Effect of die geometry on shear viscosity and entrance pressure drop determination by capillary extrusion rheometry. NPL Report. MATC(A)56

Rides, M; Allen, C R G (2002) Measuring the extensional flow behaviour of polyethylenes for plastics processing. NPL Report. MATC(MN)27

Rides, M; Allen, C R G; Dawson, A (2005) Measurement of heat transfer properties for polymer processing. NPL Report. DEPC-MN 035

Rides, M; Allen, C R G; Omloo, H*; Nakayama, K*; Cancelli, G* (2009) Interlaboratory comparison of melt flow rate testing of moisture sensitive plastics. Polym. Test., 28 (6). pp. 572-591.

Rides, M; Dean, G (1996) Evaluation of mould designs for preparing standard plate specimens of plastics by injection moulding. NPL Report. CMMT(A)30

Rides, M; Fleming, D; Allen, C R G (2006) Polymer flow incorporating slip and implications for polymer processing simulations. NPL Report. DEPC-MN 040

Rides, M; Kelly, A L*; Allen, C R G (2011) An investigation of high rate capillary extrusion rheometry of thermoplastics. Polym. Test., 30 (8). pp. 916-924.

Rides, M; Morikawa, J*; Halldahl, L*; Hay, B*; Lobo, H*; Dawson, A; Allen, C R G (2009) Intercomparison of thermal conductivity and thermal diffusivity methods for plastics. Polym. Test., 28 (5). pp. 480-489.

Rigas, G P; Shkunov, M* (2014) Solution processable semiconducting organic single crystals. Polym. Sci. C, 56 (1). pp. 20-31.

Roebuck, B (1996) Tensile tests for discontinuously reinforced metal matrix composites. Technical Report.

Ruidong Xia*,, ; Don-Seok Leem*,, ; Kirchartz, T*; Spencer, S; Murphy, C E; Zhicai He*,, ; Hongbin Wu*,, ; Shijian Su*,, ; Yong Cao*,, ; Ji Seon Kim*,, ; de Mello, J C*; Bradley, D D C*; Nelson, J* (2013) Investigation of a conjugated polyelectrolyte interlayer polymer: Fullerene solar cells. Adv. Energy Mater., 3 (6). pp. 718-753.

S

Scoggins, C A; Tomlins, P E; Bevis, M J* (1998) The effects of copper contamination on the properties of high density polyethylene. NPL Report. CMMT(A)138

Sims, G D (2002) Polymer Composites. VAMAS Bulletin, 25. pp. 29-31.

Sims, G D (2001) Polymer composites. VAMAS Bulletin, 24. pp. 31-32.

Sims, G D; Gnaniah, S J P (2005) Polymer composites - rate dependent temperature calibration of dynamic mechanical analysers (DMA) for Tg measurements. NPL Report. DEPC-MN 017

Sims, G D; Nimmo, W (1997) Reference temperature for thermal testing of polymer matrix composites. NPL Report. CMMT(MN)018

Synooka, O*, Eberhardt; Balko, J*; Thurn-Albrecht, T*; Gobsch, G*; Mitchell, W*; Berny, S*; Carrasco-Orozco, M; Hoppe, H* (2016) Thermally stable and efficient polymer solar cells based on a novel doner-acceptor copolymer. Nanotechnology, 27 (25). 254001

T

Tomlins, P E (1995) Comparison of different functions for modelling the creep and physical ageing affects in plastics. NPL Report. DMM(A)158

Tomlins, P E (1997) Crystallization kinetics in polymer melts. NPL Report. CMMT(A)66

Tomlins, P E (1999) Measurement and analysis of creep in plastics. Measurement Good Practice Guide. 2

Tomlins, P E (1997) Predicting and controlling the dimensional stability of injection moulded plastic parts. NPL Report. CMMT(A)60

Tomlins, P E (1999) Strategies for assessing the influence of pigments and processing conditions on the dimensional stability of mouldings. NPL Report. CMMT(A)201

Tomlins, P E; Read, B E (1996) Creep and physical ageing of polypropylene: A comparison of models. NPL Report. CMMT(A)23

Tomlins, P E; Read, B E (1998) Creep and physical ageing of polypropylene: a comparison of models. Polymer, 35 (2). pp. 355-367.

Tomlins, P E; Read, B E; Dean, G (1994) The effect of temperature on creep and physical ageing of poly (vinyl chloride). Polymer, 35. pp. 4376-81.

Tomlins, P E; Read, B E; Dean, G D (1993) The effect of temperature on creep and physical aging of PVC. NPL Report. DMM(A)93

Tomlins, P E; Richardson, M J (1999) The influence of phthalocyanin blue on the crystallization behaviour of polypropylene. NPL Report. CMMT(A)147

Tomlins, P E; Richardson, M J*; Shenton, M J*; Janimak, J J* (2000) The influence of pigments on the crystallisation behaviour, morphology and dimensional stability of plates injection moulded from HDPE. NPL Report. CMMT(A)217

Tomlins, P E; Rides, M; Dawson, A; Gee, M G; Dean, G D; Hobbs, C B; Allen, C R G; Gnaniah, S J P; Calver, A; Darling, R (2005) Physical characterisation of soft-touch polymers. NPL Report. DEPC-MPR 025

Tomlins, P E; Scoggins, C A (1998) Problems associated with the use of recycled plastics within the UK. NPL Report. CMMT(A)126

Tomlins, P E; Urquhart, J M; Lord, G; Butler, B P (1998) A strategy for investigating the influence of processing conditions on the dimensional stability of injection moulded artefacts. NPL Report. CMMT(A)111

Turnbull, A (1995) Degradation of plastics: towards improved charaterisation. Mater. World (April). 182 - 183

Turnbull, A; Falla, N*; Smith, A*; White, D* (1996) Accelerated weathering of UPVC. NPL Report. CMMT(A)45

Turnbull, A; Falla, N*; Smith, A*; White, D* (1997) Accelerated weathering of UPVC. J. Mater. Sci., 32 (9). pp. 2313-2327.

Turnbull, A; Falla, N*; White, D R*; Winter, T* (1996) Limitations of plasma erosion as an ultrafast weathering technique. Polym. Test., 15. pp. 455-466.

Turnbull, A; Maxwell, A S (1999) Test methods for environmental stress cracking of polymeric materials. Technical Report. NPL, UK.

Turnbull, A; Maxwell, A S; Pillai, S (2000) Comparative assessment of slow strain rate, 4-pt. bend and constant load test methods for measuring environment stress cracking of polymers. Polym. Test., 19 (2). pp. 117-129.

Turnbull, A; Maxwell, A S; Pillai, S (1999) Residual stress in polymers - evaluation of measurement techniques. J. Mater. Sci., 34 (3). pp. 451-459.

Turnbull, A; Maxwell, A S; Pillai, S; White, J R* (1998) Residual stress in polymeric mouldings. Measurement Good Practice Guide. 10

Turnbull, A; White, D*; Falla, N*; Smith, A (1997) Accelerated weathering of UPVC. J. Mater. Sci., 32 (9). p. 2313.

U

Urquhart, J M; Brown, C S (2004) The effect of uncertainty in heat transfer data on the simulation of polymer processing. NPL Report. DEPC-MPR 001

W

White, J R*; Turnbull, A (1994) Weathering of polymers: mechanisms of degradation and stabilization: testing strategies and modelling. J. Mater. Sci., 29 (3). pp. 584-613.

Woolf, A; Brown, C S (1996) Protocol for the prediction of creep of plastic components. NPL Report. CMMT(A)26

Woolf, A; Read, B E (1995) Prediction of creep behaviour of plastic components. NPL Report. CMMT(A)4

Y

Yim, K H*; Dogherty, W J*; Salaneck, W R*; Murphy, C E; Friend, R H*; Kim, J S* (2010) Phase-separated thin film structures for efficient polymer blend light-emitting diodes. Nano Lett., 10 (2). pp. 385-392.