A

Auty, F J; Bevan, K; Hanson, A; Machin, G; Scott, J; Brown, C*; Haritos, G*; Martinez-Botas, R F* (2014) Beginner's guide to measurement in mechanical engineering. Measurement Good Practice Guide. 131

B

Behnert, I D; Deadman, A J; Fox, N P; Harris, P M; Gürol, S*; Özen, H*; Bachmann, M*; Boucher, Y*; Lachérade, S* (2011) Measurement report CEOS WGCV pilot comparison of techniques and instruments used for the vicarious calibration of land surface imaging through a ground reference standard test site 2009. NPL Report. OP 5

Bennett, S; Valdes, J* (2010) Materials metrology. Metrologia, 47 (2). Foreword

Bennett, S J (2008) Citior, altior, fortior, accuratior? Metrology in Sport. Measure, 3 (4). pp. 24-28.

D

Dias, C; King, M (2024) Input Output analysis: A Pilot Study assessing the flows of NPL's impact into final demand. NPL Report. IEA 21

Dias, C; King, M (2022) A Meta-Analysis of NPL's Impact Case Studies: Charting NPL's Economic and Societal Benefit Mechanisms. NPL Report. IEA 8

F

Finsterle, W*; Blattner, P*; Moebus, S*; Ruedi, I*; Wehril, C*; White, M; Schmutz, W* (2008) Third comparison of the world radiometric reference and the SI radiometric scale. Metrologia, 45 (4). pp. 377-381.

Flowers, J L; Petley, B W (2010) Fundamental constants. In: Handbook of Metrology. Wiley VCH, pp. 33-74. ISBN 9783527406661

Foss, J*; Dewhurst, R*; Yacoot, A; Regtien, P*; Peters, K* (2013) Announcing the 2012 Measurement Science and Technology outstanding paper award. Meas. Sci. Technol., 24 (7). 070101

Foss, J*; Peters, K*; Yacoot, A; Jakoby, B*; McGrath, J* (2015) Announcing the 2014 Mesurement Science and Technology outstanding paper awards. Meas. Sci. Technol., 26 (7). 070202

G

Goldsmith, M (2010) A beginner's guide to measurement. Measurement Good Practice Guide. 118

K

Katanguru, D R; King, M (2024) Assessing the reach and impact of the NMS laboratories on UK private sector businesses. NPL Report. IEA 24

Kibble, B P (2012) Measurement for the future - a complete SI from physical constants. IEEE Trans. Instrum. Meas., 61 (8). pp. 2125-2131.

King, M; Renedo, E (2020) Achieving the 2.4% GDP target: the role of measurement in increasing investment in R&D and innovation. NPL Report. IEA 3

M

Machin, G (2014) Measurement fundamentals: an introduction. Meas. Control, 47 (10). p. 301.

Martin, O C*; Muelaner, J E*; Dhokia, V*; Robson, S*; Kayani, A; Maropoulos, P G* (2016) Comparative performance between two photogrammetric systems and a reference laser tracker network for large-volume industrial measurement. Photogrammetric Record, 31 (155). pp. 348-360.

Milton, M J T (2012) Making progress in a practical discipline. Accred. Qual. Assur., 17 (2). pp. 221-222.

N

Nayak, Srajal; Yildiran, C; Dias, C; King, M (2024) Visualising the Locations of NPL’s SED Departments and Designated NMS Laboratories Within an Impact Space. NPL Report. IEA 22

Q

Quincey, P G; Brown, R J C (2016) Implications of adopting plane angle as a base quantity in the SI. Metrologia, 53 (3). pp. 998-1002.

R

Ridler, N M (2016) The MTT-S standards coordinating committee- developing IEEE standards. IEEE Microw. Mag., 17 (9). p. 82.

Rowley, W R C (1992) Rapport au Comit‚ International des Poids et Mesures. Technical Report.

T

Torr, G (2013) A viewpoint on innovation-based industrial competitiveness. Meas. Control, 46 (5). pp. 154-156.

W

Williams, E*; Robinson, I A (2011) Superconductivity and the SI (Metric) systems based on fundamental constants. In: 100 years of Superconductivity. Taylor & Francis. ISBN 9781439849460

Wooldridge, J; King, M B (2019) Altmetric scores: An early indicator of research impact. Journal of the Association for Information Science and Technology, 70 (3). pp. 271-282. ISSN 2330-1635